Select a Country or Area
|
Contact Us
Products & Services
Technical Support
Industries
Buy
About Agilent
Home
>
Technical Support
>
FAQs
>
Liquid Chromatography
>
Hardware
>
LC/MS Hardware
Register
|
Login
Frequently Asked Questions
Downloads and Utilities
Education & Events
Frequently Asked Questions
DNA MicroArrays
Gas Chromatography
Lab-on-a-Chip
Life Sciences Informatics
Liquid Chromatography
Mass Spectrometry
Networked Data Systems
Proteomics
Installation and Maintenance Videos
Literature Library
Parts Information
Description, Pricing, and Availability
Illustrated Parts Breakdowns
Support Services - Finding
Warranty Status - Verifying
Please select a topic from this section below:
1050 Series LC Hardware
1090 Series LC Hardware
1100 Series LC Hardware
1200 Series LC Hardware
Capillary Electrophoresis (CE) Hardware
General LC Hardware
LC/MS Hardware
LC/MSD IonTrap
UV/Vis Hardware
Click a question below to see the answer:
Unwanted 76 and 134 m/z peaks in my G1956B LCMS scan.
How much nitrogen gas is required for LC/MSD operation?
Why is Nitrogen Required in Standby mode?
What are the LC/MSD Standby Conditions?
What are the options for supplying dry nitrogen for the LC-MSD?
Should I worry if the <b>MSD Ion Optics Test</b> gives a ''Quad DC Fault''?
How do I add a solution post-column to enhance the performance of the electrospray ion source?
How can I find a part number if I only have a description?
How do I get a copy of a Material Safety Data Sheet (MSDS) online?
How do I place an order for consumables?
How is the Agilent LC/MSD System affected by the strength, effects, and interference of magnetic field environments?
What are the venting requirements for my LC/MSD hardware
What are the specifications of Agilent 1200 series LC/MSD?
What are the specifications of the Agilent 6300 Series Ion Trap LC/MS Systems?
What are the features of Multimode ion Source ?
What is Agilent Quiet Cover (G3199A) for LC/MS?
Why are ionic detergents not allowed in my sample solvent?
My sample is not very soluble unless I add SDS, is this ok?
Why would I use LC MS/MS instead of MALDI for peptides?
What salts or components should I avoid with LC-MS/MS?
Why low Response for my compound in ESI source compared to Multimode Source?
'A LEAK' message appears in the MSD unit - but there is no leak observed in actual leak sensor area. What could be the problem?
Why there is very little oil remaining in the rotary (rough) pump which causes the pump to shutdown intermittently on its own. But it is observed that,there is no oil spillage in the tray. What could be the problem?
Why does venting not complete even after one hour while performing venting through ChemStation?
Is there a way of venting the MSD other than from ChemStation?
Why does the MSD is shut down just before starting measurement and a message in the log book indicates an error such as the nebulizer pressure or dry gas flow? But there is no shutdown in standby mode.
Why are no ions being seen while performing the tune? Only baseline noise is observed?
Why ChemStation does not detect the MSD even when it restarts?
How can I get the MSD data without turning on the DAD lamp?
Why I am getting the error 'electronics capillary chamber voltage could not be maintained' during measurement?
How can I use only the LC and not the MSD in my LC-MS system?
What Is Tuning? What parameters are adjusted while tuning?
What is the result of tuning? How are the results of tuning used?
How do I tune the LC/MSD from the ChemStation software?
What is the Nitrogen Gas Consumption for Agilent LC/MSD?
What are the points to be considered if I want to use THF in my LCMS system?
What are the tips used to increase the signal to noise ratio of my LCMSD?
Why I am getting ion 331 contamination and how do I eliminate it?
Why am I getting high noise in high mass region of the spectrum?
Why am I getting repetitive,distinctive polymer type ions in my MS spectra?
What are the part number of Replacement Membranes for LC/MS Nitrogen Generators?
Why I am getting ions 371,445 and 519 in my LCMS system?
How do I know which type of Nitrogen Generator I have?
What is Capillary Charging Test in LCMS systems?
What is Capillary Passivation Procedure in LCMS systems?
What type of LC cleaning solvent mixture can be used to steam clean the LCMS systems?
What is the purpose of a Gas Ballast Control in an LCMS system?
Why does the Nitrogen Gas Purifier is heating up during its installation?
How often should the Nitrogen Gas Purifier be replaced?
What is steam cleaning in LCMS?
What are the features and benefits of Multimode LC/MS Source?
What is an Organic MS?
What is an Inorganic MS?
Why I am getting Negative Peaks in the Mass Spec Chromatogram?
When do we replace the rough pump oil?
What solvents to be used to flush the HPLC lines to remove contaminants?
How can I enlarge the offline chromatogram window as it gone very small during operation?
No compound found with Multimode source. Why?
What is the part number for Multi mode source IR Emitter?
Why IR emitters are used in Multimode Source?
How to tune the Multimode source?
How to Bake out LC/MS?
Why we need to bake out LC/MS?
What are the operation modes of Multimode source?
My LC/MSD Autotune reports Mismatch Error on Quad Frequency after Software Upgrade, what could be the problem?
Can I use a G6410A Triple Quad LC/MS system with my older G1948A API Electrospray Source?
How to prepare LC/MSD Performance Evaluation Standards ?
What is the procedure for bake out of LC/MSD?
How to Shutdown the G1946 LC/MSD after Computer Failure?
Why my G1946 LC/MSD Fails the Vent Test ?
What causes the G1946 LC/MSD Turbo Pump 2 Peak Power Too High Test Failure?
What causes the G1946 LC/MSD Turbo Pump 1 Peak Power Test Failure?
MY G1946 LC/MSD Vacuum Test Fails with High Vacuum Steady State > 1 torr. Why?
MY LC/MSD ( G1946 )High Vacuum Steady State < 5^ -5 torr Test Failed. What causes this?
How to troubleshoot Vacuum problem with LC/MSD?
Why my LC/MSD signal is unstable?
What causes undesired fragmentation in LC/MSD?
Why my LC/MSD is showing poor mass accrracy?
Why my LC/MSD signal values are low?
What is the cause for High Spectral Noise in LC/MSD Signal ?
How do I connect non-Agilent made detectors to my Agilent LC/MS ChemStation?
What is the Passivation procedure for Agilent HPLC?
What needs to be done to take care of DST changes on upgraded installations of ChemStation B.02.01 and higher, with or without ChemStore B.03.03?
What needs to be done to take care of DST changes on ChemStation B.01.0x, with or without ChemStore B.03.02?
Agilent Intelligent Services Overview - LC/MS
What is Agilent Intelligent Repair?
Agilent Intelligent Connections Overview - LC/MS
Agilent Intelligent Connections Plus Overview - LC/MS
Who determines the access level to our systems while using the Agilent Intelligent Services?
Security of Agilent Intelligent Services - LC/MS
